Main parameters
| Name | Value |
|---|---|
| Rated voltage, V | 63…450 |
| Rated capacitance, µF | 100…2 200 |
| Temporary overvoltage within 10 sec., V | 1.15 UR (UR≤315) 1.1 UR (UR>315) |
| Capacitance tolerance (25 °C, 50 Hz), % | +50…-20; ±20 |
| Maximum operating temperature Tenv, °C | +125 |
| Minimal operating temperature Tenv, °C | -60 |
А = 16.5 ± 0.15 mm
1 – Positive terminal
2 – Bead
3 – Case
4 – Lengthwise swage
5 – Isolation sleeve
6 – Lacquer coating
2 – Bead
3 – Case
4 – Lengthwise swage
5 – Isolation sleeve
6 – Lacquer coating
Capacitor electric parameters value when delivered
| UR, V | CR, µF | tg δ, %, 25°C, 50 Hz, max | ILEAK, µA, 25°C, after 5 min., max | Z*, Ohm, 25°C, max | IR, А, 85°C, 50 Hz, max |
|---|---|---|---|---|---|
| 63 | 2 200 | 25 | 4 178 | 0.8 | 1.24 |
| 100 | 1 000 | 3 020 | 0.35 | 0.89 | |
| 160 | 4 820 | 0.5 | 1.46 | ||
| 250 | 330 | 20 | 2 495 | 1.2 | 0.86 |
| 470 | 3 545 | 0.9 | 1.2 | ||
| 315 | 220 | 2 099 | 1.2 | 0.69 | |
| 330 | 3 138 | 0.9 | 0.96 | ||
| 470 | 4 461 | 0.8 | 1.27 | ||
| 350 | 220 | 2 330 | 1.0 | 0.72 | |
| 330 | 3 485 | 0.8 | 0.99 | ||
| 470 | 4 955 | 0.7 | 1.32 | ||
| 400 | 100 | 1 220 | 1.3 | 0.43 | |
| 220 | 2 660 | 0.9 | 0.82 | ||
| 330 | 3 980 | 0.7 | 0.14 | ||
| 470 | 5 660 | 0.6 | 1.54 | ||
| 450 | 100 | 1 370 | 1.4 | 0.42 | |
| 220 | 2 990 | 0.9 | 0.76 | ||
| 330 | 4 475 | 0.7 | 1.05 |
* Capacitor impedance Z is measured at frequency 100 kHz for capacitors CR ≤1 000 µF, and at frequency 10 kHz for capacitors CR > 1 000 µF
Capacitors overall dimensions and mass
| UR, V | 63 | 100 | 160 | 250 | 315 | 350 | 400 | 450 |
|---|---|---|---|---|---|---|---|---|
| CR, µF | DxH, mm mass, g |
|||||||
| 100 | 40x45 90 | 40x45 90 |
||||||
| 220 | 40x45 90 | 40x55 110 | 40x65 130 | 45x50 125 |
||||
| 330 | 40x55 110 | 40x60 120 | 40x60 120 | 45x65 160 | 45x65 160 |
|||
| 470 | 40x60 120 | 40x80 160 | 45x65 160 | 45x75 190 | ||||
| 1 000 | 40x60 120 | 40x80 160 | ||||||
| 2 200 | 40x60 120 | |||||||
Ripple current effective value
versus temperature and frequency can be found from the formula IRO = IR x KT x KF, where
IR– allowable ripple current at 85 °C, 50 Hz (See Table “Capacitor electric parameters”)
versus temperature and frequency can be found from the formula IRO = IR x KT x KF, where
IR– allowable ripple current at 85 °C, 50 Hz (See Table “Capacitor electric parameters”)
KT - IR correction factor versus temperature
| Tenv, °C | 25 | 40 | 50 | 60 | 70 | 85 | 125 |
|---|---|---|---|---|---|---|---|
| KT | 1.43 | 1.37 | 1.31 | 1.25 | 1.17 | 1.0 | 0.25 |
KF - IR correction factor versus frequency
| F, Hz | 50 | 100 | 300 | 600 | 1 000 | 10 000 | ≥50 000 |
|---|---|---|---|---|---|---|---|
| KF | 1 | 1.25 | 1.5 | 1.63 | 1.69 | 1.88 | 2.0 |
Capacitors reliability
| Reliability Operation modes | Minimal nonfailure operating time, tλ, hours | Capacitor failure rate, λ, 1/hour, max |
|---|---|---|
| Maximum-permissible mode (0.7UR, Tenv=125 °С) | 6 000 | 2x10-6 |
| Maximum-permissible mode (UR, Tenv=85 °С) | 40 000 | 5x10-7 |
| Light mode (0.6UR, Tenv=60 °С) | 300 000 | 3x10-8 |
| Light mode (0.6UR, Tenv=85 °С) | 110 000 | 10-7 |
| Storageability Gamma-rated time of capacitor storageability Tcy at y=99.5%, years, min | 25 | |
Voltage versus temperature
UT
UR
UR
T, °C
